子程序:
' U' ?& T! F% e9 j- ~' |T0101
9 O. h: V* n7 {* g5 k' TM3S600' s; C" a. x% _2 f0 A
M08: V) F% w: F1 Q( m) ^. x3 g
G99
/ M: U' g% o+ b$ _* B6 `9 Q( o- FG0X16
) P( X3 G/ O3 |. r* JZ2
, h0 z1 X$ K, cG94X3Z0F0.154 f* e3 t% @. u/ `5 J! J* m+ |6 I5 L. P
G90X12.4Z-10.5
6 k1 Y/ ?( _9 }3 Z' |X11.8
+ Y/ V+ \( a2 f3 JG0X10.5
* F5 ^* `. {) P: G( OG1Z-2.5) N* K( Q. K, j8 P- g- z5 R9 R+ _: E
X10.8( p; p+ V/ D1 G& j$ ]* L3 q
G0Z1
; r* P8 a5 \& uX10
6 r; P% V& u' f/ J. d7 aG1Z-2.51 x5 q2 ]' O% R4 r. w, o9 x
X10.2) j# W6 w. L. Z: P2 t
X11.9W-1
, h! ?/ y: \) @& v$ CG0Z0! [4 y0 B' r, G0 y
X10.3
! y2 S8 b; t$ x$ B# WG1X9.4
8 X. U# \$ [6 d7 Y# ZX10.1Z-0.3
2 T7 j! j% A$ d/ F6 d( C+ pG0X50Z1508 D2 h9 ^6 J- M# _
T0202# _, W5 @! k+ ~: Q
G0X12.15 Z, f; L: U4 o- D e0 x
Z-10
1 r% M: _- E2 d K8 tG1X10F0.053 k, n [7 I2 G2 N/ Y8 ?, V
G0X12.1
) t, d8 Q2 Q- c# vZ-9, z8 v6 Y2 Y) d
G1X11.9$ ^& |0 x* S K2 c. v$ a, P5 ~7 h8 c
X10Z-10! V" k* n) T; G2 z# k
G0X50" O* D/ w; ^6 a1 U/ G; y
Z150
/ k0 w( w* Q: ^0 PT0303! D4 C9 u9 `3 S( N
G0X12.52 o( Y, ?% e, j3 J
Z3
' d5 J" j- G; u" ?0 c4 D( ^. lG92X11.3Z-8F1
0 u# ~5 O! d- o ` }1 Y1 E+ uX11
' V4 y) p0 t# U9 iX10.8, W+ y0 m& Q1 v% k
G0X50
5 o1 y% w% }- ]* r% k. I) ]Z150% s' [3 b/ M+ l* V/ C
T0404
( i2 Z3 s) K4 V, ]" W3 u& Q* |' AG0X69 d: @0 _3 g+ {+ `6 b1 ]' d: m+ X2 d
Z1
* G* M. s) I3 Z2 v3 z7 _G1Z-3.5F0.1
6 ~- s, X% L( N( o0 _' ]3 I* [X5.8
' q8 B! }5 C% D) E5 _) UG0Z1
1 F7 {. a ]& ?# p) }9 S* N6 jX6.71 W3 V. P' D9 y( F
G1Z-3.5
+ m D3 P$ x, i8 Q- n. i$ O: o5 ]2 m \3 aX6.5
: @/ N' S% P t/ qG0Z1
- G9 h4 } j! m0 R4 u! i. P7 v1 VX76 j, s' D! ?+ G5 x& O0 c2 b
G1Z-3.5* p/ V1 k2 G8 w+ w
X6.8
( B% a% T# }6 H# l# F# @' I7 rG0Z0' _; @ p5 Z! K
G1X7.4
! Q) l4 l" x/ ~$ L+ i' b) YX6.9Z-0.2! a% j" i+ M3 f H9 h1 H/ ?
G0Z150
4 ?7 U6 J( j9 y [6 J. Q& ]X50
9 `* d4 T0 t$ B; w; c& dT0202# l! M: X5 _8 C- _
G0X12
* J# \( l% P& H' U7 pZ-10/ O! {% X. [( q7 z1 F [2 Z
G1X3.5F0.03
t) L& a: H% W1 P$ MG0X50- T: p1 |; z Y
Z1508 W8 a- `1 E8 e, t, u
M99
5 g$ V- K3 T8 a" u8 n
& X1 }+ T/ ^6 R) A- i: _% E主程序:
7 O7 f4 ~# z; b* U, Y' JG10P0Z0$ b/ L; g! m0 M9 l- r( F
M98P00128 a% }' W5 P, ^( C4 [8 ?
G10P0Z-10.1% {1 B' W$ k6 @
M98P0012
; f/ I6 A: O/ N# bG10P0Z-20.2: j& i5 [5 X: c0 y: z# W
M98P0012: P0 o; \8 p3 k8 \2 ?2 l1 V
M99
" P, ?3 l# P/ L* L8 bG50Z150* S6 N1 k, e: p7 K; i6 [3 u7 Y
M30& |! _6 h" ?2 W1 K, }5 M
4 x- U$ h, M0 f9 z% M; Y: N
用子程序加工单个零件时正常,被主程序调用后G90的走刀方向都反了,不知是什么原因,求高手解答。 |